CAD/CAM ve 3D Yazıcılarla Üretilen Zirkonyanın Renk Stabilitesi Üzerine Farklı Yüzey Bitirme İşlemlerinin Etkisi


Yeşil Z., Abo Haoran M., Yeşil Ç.

The 48th Annual EPA Congress and The 27th Scientific TPID Congress, Nevşehir, Türkiye, 11 - 13 Eylül 2025, ss.26, (Özet Bildiri)

  • Yayın Türü: Bildiri / Özet Bildiri
  • Basıldığı Şehir: Nevşehir
  • Basıldığı Ülke: Türkiye
  • Sayfa Sayıları: ss.26
  • Recep Tayyip Erdoğan Üniversitesi Adresli: Evet

Özet

AMAÇ: Bu çalışmanın amacı, CAD/CAM ve 3D yazıcılar ile hazırlanan zirkonyumun renk stabilitesi üzerinde farklı yüzey bitirme işlemlerinin etkisini araştırmaktır.

GEREÇ VE YÖNTEM: Çalışmada, Uluslararası Standardizasyon Örgütü (ISO 6872) standartlarına uygun olarak, 15 mm çapında ve 1,2 mm kalınlığında disk şeklinde toplam 40 örnek, CAD/CAM ve 3D yazıcı kullanılarak hazırlanmıştır. Örneklerin yalnızca bir yüzeyine, üretici firma önerileri doğrultusunda glazür uygulanmıştır. Numaralandırılmış örneklerin ilk renk ölçümleri spektrofotometre kullanılarak yapılmıştır. Her gruptaki örneklerin yarısı, aynı araştırmacı tarafından, yüksek devirli bir el aleti ve ince taneli elmas frez kullanılarak, tek yönlü bir hareketle 15 saniye boyunca aşındırılmış; ardından örnekler distile su ile yıkanıp hava ile kurutulmuştur. Aşındırılan örneklerin yüzeyleri, üretici firma önerileri doğrultusunda OptraGloss seramik parlatma seti ile bitirilmiş ve renk ölçümleri tekrarlanmıştır. Tüm gruplardaki örneklerin yarısına 5000 döngü yaşlandırma işlemi uygulanmış ve renk ölçümleri tekrar yapılmıştır. Renk değişimleri, CIEDE2000 renk farkı (∆E00) formülü kullanılarak belirlenmiştir. Elde edilen veriler, SPSS-22 yazılımı kullanılarak varyans analizi ve Tukey çoklu karşılaştırma testleri ile analiz edilmiştir.

BULGULAR: Verilerin değerlendirilmesi için kullanılan varyans analizi sonucunda; üretim yöntemi ve yüzey bitirme işleminin oldukça anlamlı (p<0,001), yaşlandırma işleminin anlamsız (p>0,05) olduğu; üretim yöntemi ile yüzey bitirme işlemi arasındaki etkileşimin ise anlamlı (p<0,005) olduğu saptanmıştır.

SONUÇ: Bu çalışmada, en fazla renk değişiminin 3D yazıcı ile hazırlanan ve parlatma seti ile yaşlandırma işlemine tabi tutulan örneklerde görüldüğü belirlenmiş olup, 3D yazıcı ile üretilen örneklerin geliştirilmesi gerektiği sonucuna varılmıştır.

OBJECTIVE: The aim of this study is to investigate the effect of different surface finishes on the color stability of zirconia prepared by CAD/CAM and 3D printers. MATERIAL-METHODS: In the study, a total of 40 samples in the form of discs with a diameter of 15 mm and a thickness of 1.2 mm were prepared with CAD/CAM and 3D printer in accordance with the International Organization for Standardization (ISO 6872) 89. Only one surface of the specimens was glazed according to the manufacturer’s recommendations. The first color measurements of the numbered samples were made using a spectrophotometer. Half of the samples from each group were etched with a high-speed power tool and a finegrained diamond bur for 15 seconds in a unidirectional manner by the same researcher, after which the samples were washed with distilled water and air-dried. The abraded specimens were surface finished with OptraGloss ceramic polishing restoration kit according to the manufacturer’s recommendations and color measurements were repeated. Half of the specimens in all groups were subjected to 5000 cycles of aging and color measurements were repeated. Color changes were determined using the CIEDE2000 color difference (∆E00). The data obtained were analyzed by analysis of variance and Tukey multiple comparison tests using SPSS-22 software. RESULTS: As a result of the analysis of variance used to evaluate the data; it was determined that the production method, surface finishing process was very significant (p<0.001), aging process was insignificant (p>0.05), and the interaction of production method and surface finishing process was significant (p<0.005). CONCLUSION: In this study, it was determined that the most color change was observed in the samples prepared with the 3D printer polish kit and aging process, and it was concluded that the samples prepared in the 3D printer should be improved.